Jump to content

Recommended Posts

Posted (edited)

For starting:

this is not a beginners guide! just a list of helpful suggestions what could have gone wrong

I am using a decentralized setup, my connect Box is about 5 meters away from my PC, so there is the first problem: 

USB 3.x is not able to transmit data over 3m+ even Displayport can have connection Problems at this range. Use "active" extension cables witch allow to extend to up to 15m without additional Power source. With the App UsbTreeView you can see in Realtime if your HTC USB devices are connected or not (at least 5 additional entries in list)

Next issue Was my damaged active usb 3.1 extension cable. In UsbTreeView i saw 2 devices connected but Installation guide didnt Show "found USB connection" after twisting and turning (dont try this at home) i found out that my extension had a lose ground contact. Always use functional cables or it will not work properly or even damage your System.

On this way i got frustrated because i knew it must work because i used the htc vive pro(1) before and so i tried many Things like reinstall steam, vive Software, steam vr and even a clean Windows Installation, wich led to the next problem: i installed my Standard Tools for system overclocking etc. Installed Steam and started a fresh Installation of vive Software and SteamVR, it worked but the relieve lasted not long. SteamVR started and told me to connect my VR-Headset, wich already was so i got confused. I checked evry cable and connection. I looked up evry driver and firmware, nothing worked. I even installed beta builds of vive console and SteamVR none did work. 'Till i started SteamVR via Desktop shortcut, and a steam popup came wich told me "first time Installation, installing vc redist, DirectX and .net framework etc. Concludes: after a fresh Installation of your htc device and SteamVR close all Windows and run SteamVR via Steam Launcher, otherwise it wont install neccesery tools wich are NEEDED to run your vr System. Or install it manually.

But finally it works fine and can perform greatly under a 3080Ti even on Ultra settings (highest ressolution, 150% and 120hz) but the eye distance is slightly too small. Have 72mm and the vive pro 2 can provide only 70,5mm

tl:dr

Dont use cable longer than 3m or use active extensions (USB 3.0 and/or DP1.4 compatible)

Dont use standards older than USB 3.0/DP 1.4 

Always check cable condition (buy New if much too wrinkly or visibly damaged or folded)

Check if drivers are installed and loaded (my recommendation: UsbTreeView)

Check if ALL NECCESARY Programms, frameworks, tools, firmwares and drivers are installed. 

I hope i Was of help for you, and sory for the bad grammar

 

Edited by oT_BonEo
Posted

Another Problem i ran into:

My MSI RTX 3080Ti Gaming X Trio does not support more than 4 Monitors.

This can be easily fixed by disabling the Monitor/s via Windows Display settings. Or just by pluging them out. Be aware that pluging your Monitors resets their settings and can cause changes in appearence if you use multiple Desktops and different settings like wallpapers or ressolutions.

Your vive counts as 2 (two) Monitors so if you natively use 4 Monitors in your setup you have to unplug/disable 2 of them for your vive to start.

Posted
1 hour ago, oT_BonEo said:

Another Problem i ran into:

My MSI RTX 3080Ti Gaming X Trio does not support more than 4 Monitors.

This can be easily fixed by disabling the Monitor/s via Windows Display settings. Or just by pluging them out. Be aware that pluging your Monitors resets their settings and can cause changes in appearence if you use multiple Desktops and different settings like wallpapers or ressolutions.

Your vive counts as 2 (two) Monitors so if you natively use 4 Monitors in your setup you have to unplug/disable 2 of them for your vive to start.

Same with Pimax 8K and Vive Pro 2, this is a limitation for all graphics cards. The limitation is 2 monitors + 1 VR headset. It will state maximum displays if you have 3 monitors + 1 VR headset.

I use WIN + P to either go to PC screen only or right click desktop, display settings and select monitor 3 and disconnect it.

That's the problem with high resolution VR now.

If you're in High resolution, just like wireless, it's not a problem. 3 monitprs + high resolution VR (not 5K).

Posted

Another solution for multimonitoring + High res VR could be a secondary graficscard so you can use 2-4 side Monitors on a low end cheap card, like an gtx 900 series and using gaming Monitor + vr on the Main card. But it could be problematic with the PCIe lane count. Using another card costs at least 4 lanes (idk. If this is a Thing with PCIe 4.0)

If you try to use multiple monitors for gaming (Like Ultra wide view) and VR, there might be only the option of using 2 cards in nvlink/crossfire. But at this Moment it would never be worth the effort and price.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...